Skip to content

Ask the bay

166 questions drivers, owner-operators and fleet managers actually ask, answered by the people who do the work. Type to filter.

Semi Truck Repair

Open the page
How fast can you get my semi truck repaired in Toledo?

Diagnosis happens the day you drop the truck. Most common repairs, like brake chambers, air dryers, alternators, belts, hoses and sensors, are done the same day when the part is on our shelf. Rebuilds and engine-out jobs take longer and the timeline is on the estimate.

What truck and engine brands do you work on?

Freightliner, Peterbilt, Kenworth, Volvo, International, Mack, Western Star and Hino, with Cummins, Detroit, Caterpillar and Paccar engines. Our techs hold Cummins and International certifications on top of ASE.

Do I get a price before you start?

Yes. You get a written estimate with parts, labor and timeline after diagnosis and before any repair begins. Call for the current labor rate.

Are the repairs covered by a warranty?

Yes. We are a certified NAPA Truck Care Center and repairs are backed by the NAPA nationwide warranty, so a covered failure can be handled at another NAPA truck service location on the road. The written terms are on our warranty page.

Do you handle Class 8 trucks or just medium duty?

Both. The shop is built for Class 4 through Class 8 trucks and trailers, from box trucks to tractors.

Do you repair truck AC?

Yes. AC recharge and repair, heater core service, thermostats, water pumps, radiators and hoses are all done in-house.

Can you align the truck after suspension work?

Yes. The Hunter HawkEye XL heavy-duty alignment system is in the same shop, so a truck that had kingpins, tie rods or springs replaced can be aligned before it leaves.

Mobile Truck Repair

Open the page
Do you offer mobile truck repair at night or on weekends?

No. The service truck runs during shop hours, Monday to Friday 8:00 AM to 5:00 PM. If the truck goes down after hours, call at 8:00 AM and you are at the front of the line.

What can actually be fixed on site?

Air leaks, glad hands and lines, brake chambers and slack adjusters, batteries, starters, alternators, belts, hoses, fuel filters, lighting and trailer cords, landing gear, door and latch repair, and mobile MIG and TIG welding on frames, crossmembers and hangers.

What cannot be fixed on site?

Transmission and clutch work, engine-out repairs, injectors and turbos, alignment and anything that needs a lift. We tell you that on the phone and help with the tow to the shop.

How far will the service truck go?

The Toledo area: Toledo, Sylvania, Maumee, Perrysburg, Northwood, Oregon, and out the I-75, I-280, US-23 and Turnpike corridors. Tell us the location and we confirm on the call.

Do you do yard service for fleets?

Yes. The same service truck does preventive maintenance and light repair at fleet yards in the Toledo area on a schedule, so the trucks never leave the lot.

What does a mobile call cost?

Call for the current rate. You get the travel and labor figures before the truck leaves, and the parts figure once the tech has eyes on the problem.

Emergency Truck Repair

Open the page
Do you offer emergency truck repair at night or on weekends?

No. We are open Monday to Friday, 8:00 AM to 5:00 PM, and we do not have after-hours coverage. During those hours a breakdown goes to the front of the line. If the truck goes down after 5, call at 8:00 AM and you are first.

How fast can you respond?

During shop hours, right away: we clear a bay or send the service truck on the call. Arrival depends on where you are in the Toledo area, and we give you a window before we hang up.

Do you come to the truck?

Yes, during shop hours, for repairs that can be done on site: air leaks, brakes, batteries, starters, alternators, belts, hoses, fuel filters, lighting and mobile welding. Engine-out, transmission and alignment work needs the bay, and we say so on the phone.

What if I break down on I-75 near Toledo?

Get off the travel lane, hazards on, triangles out at 10, 100 and 200 feet, then call (419) 724-2475. The shop is at 820 Matzinger Rd a mile off I-75 exit 207 (Stickney Ave), so a tow to us is short from anywhere between the Michigan line and Perrysburg.

Is emergency repair more expensive?

The labor rate is the same rate as scheduled work. Call for the current rate. A mobile call adds travel, which we quote before the truck leaves.

What should I have ready when I call?

Location with exit or mile marker, what the truck is doing in your words, whether it is loaded, what you have tried, and the truck and engine make if you know them.

Can you handle a derate or DPF problem on the spot?

We diagnose it the same day. A forced regen or a sensor is often same-day. A DPF that needs cleaning or replacement depends on parts, and we tell you which it is before the work starts.

DOT Annual Inspection

Open the page
How often is the DOT annual inspection required?

At least once every 12 months for every commercial motor vehicle, per 49 CFR 396.17. That includes trailers. The carrier keeps the report for 14 months and proof of the inspection stays on the vehicle.

How long does the inspection take?

About an hour per unit. A tractor and trailer together is about two hours, plus any repair.

What happens if the truck fails?

You get the list of items, what each one takes and whether the part is on the shelf. Most are repaired the same day in the same bay, the item is re-inspected and the report is completed. The truck does not leave with an open item unless you decide to take it.

Do you inspect trailers?

Yes. Dry vans, flatbeds, reefers, lowboys, step decks, tanks and hoppers. Trailers are inspected on brakes, air lines, suspension, frame, floor, lighting, reflective tape, tires, wheels, landing gear and coupling.

Who performs the inspection?

A qualified inspector under 49 CFR 396.19, with the training and experience the rule requires, at a certified NAPA Truck Care Center staffed by ASE certified technicians.

What does the inspection cost?

Call for the current rate. The inspection is a flat fee per unit. Any repair is quoted separately in writing before it starts.

Can a fleet schedule all its units?

Yes. Fleets put the annual on a calendar by unit, run it with the PM, and get the reports filed for the FMCSA record. That is part of the fleet maintenance program.

Trailer Repair

Open the page
What types of trailers do you repair?

Dry vans, flatbeds, reefers, lowboys, drop decks, step decks, dump trailers, tank trailers, grain hoppers and livestock trailers.

Do you do trailer welding and structural repair?

Yes. MIG and TIG welding for frame straightening, crossmember repair and replacement, subframe welding, crack repair and custom fabrication, in the shop or on site from the service truck.

Can you repair trailer brakes and air systems?

Yes. Air line replacement, glad hands, air tanks, brake chambers, slack adjusters, air dryers, linings and drums, plus the leak-down test to prove it holds.

Do you replace trailer floors?

Yes. Wood floor replacement, aluminum floor repair, crossmember repair under the floor, threshold plates and scuff liner. Partial floor sections where the rest is sound.

How do I know if my trailer needs repair?

Soft spots in the floor, a door that will not seal, lights that flicker, an air leak you can hear with the brakes set, a landing gear crank that binds, or uneven tire wear on one axle. Any of those is a roadside item waiting to happen.

Do you offer same-day trailer repair?

Often, for lighting, air lines, glad hands, brake chambers, landing gear and latch work, when the part is on the shelf. Floors, doors and structural welding get a timeline with the quote.

Can you align trailer axles?

Yes. The Hunter HawkEye XL reads tractor and trailer axles, so an axle that is scrubbing tires can be measured and corrected in the same shop.

Reefer Repair

Open the page
Do you repair reefers at night or on weekends?

No. We are open Monday to Friday, 8:00 AM to 5:00 PM, with no after-hours coverage. During those hours a reefer with a load goes to the front of the line. After hours, keep the doors shut, run the unit if it runs, and call at 8:00 AM.

What should I check before I call?

The reefer fuel tank, the setpoint against the box temperature, the alarm code on the controller, whether the unit is in continuous or cycle-sentry mode, and whether the doors are sealed. Half of the reefer calls we get are fuel, a door, or a setting.

Do you come to the trailer?

Yes, during shop hours, in the Toledo area. Fuel, battery, belt, electrical and door and seal work is often done where the trailer sits. Floors, chutes, bulkheads and refrigeration circuit work usually come to the bay.

What brands of reefer units do you work on?

Call with the unit make and model and we tell you straight on the phone whether it is ours or a unit dealer's job. We are independent and we would rather say so than hold your trailer.

Will you repair the trailer too, not just the unit?

Yes. Doors, seals, hinges, latches, air chutes, bulkheads, floors, drains, insulation damage, lighting, air lines and brakes. The trailer side of a reefer is where most air leaks come from.

How do I document the temperature for a claim?

Download the unit controller log before anything is cleared or reset, and photograph the controller and the box thermometer when you find the problem. We do not clear codes until they are recorded.

Semi Truck Tire Service

Open the page
Do you do roadside tire service at night or on weekends?

No. The service truck runs Monday to Friday, 8:00 AM to 5:00 PM. There is no after-hours coverage. During those hours a truck on the shoulder goes to the front of the line.

Do you have my tire size in stock?

Common sizes for tractors and trailers are usually on hand, and we confirm on the call before the truck leaves. If you carry a spare, say so, and the change-out is faster. We can also mount a tire you supply.

Can a flat be repaired or does it need replacing?

A puncture in the tread area within the repairable zone can be repaired from the inside with a proper patch and plug once the tire is dismounted and the carcass is inspected. Sidewall damage, shoulder punctures, run-flat damage and exposed cord mean a replacement.

Why does one tire keep wearing on the inside edge?

Usually alignment: toe or camber on a steer axle, or a trailer axle out of square. A new tire on a misaligned axle wears out the same way. The HawkEye XL reads three axles at once so the cause is measured, not guessed.

What is the minimum legal tread depth?

4/32 of an inch on steer tires and 2/32 on all other positions, measured in a major groove, per 49 CFR 393.75. Any tire with cord or belt showing is out of service regardless of depth.

What does a roadside tire call cost?

Call for the current rate. You get the travel and labor figure before the truck leaves and the tire price on the call once we know the size.

Fleet Maintenance

Open the page
What does a fleet maintenance program include?

PM intervals set per unit, the annual 49 CFR 396.17 inspection rolled into the schedule, DVIR follow-through, maintenance records by unit kept to 396.3, priority scheduling, yard service from the service truck, consolidated billing and a single point of contact.

Can you handle a mixed fleet?

Yes. Class 4 through Class 8, trucks and trailers, Freightliner through Hino, with Cummins and International certified techs on staff. A box truck and a Class 8 tractor can be on the same calendar and the same bill.

Do you come to our yard?

Yes, during shop hours, in the Toledo area. The service truck does PM and light repair at your lot on a standing day, so the units never leave. Alignment, engine and transmission work comes to the shop.

What records do we get?

A maintenance record by unit, the annual inspection reports, and the findings list from each PM, kept the way 49 CFR 396.3 requires for an audit: one year while the unit is in service and six months after.

Do you offer fleet pricing or terms?

Fleet accounts get consolidated billing and net terms on approval. Call for the current rate and we go through it with the unit count in front of us.

How is the program priced?

Per PM and per repair, quoted before the work starts, not a flat monthly fee. Call for the current rate.

How do we get started?

Call (419) 724-2475 or send the request form with the unit count. We walk the fleet, set the intervals and the calendar, and the first PM day is usually within the week.

Diesel Engine Repair

Open the page
Which diesel engines do you work on?

Cummins, Detroit, Paccar, Caterpillar and International engines in Class 4 through Class 8 trucks: Freightliner, Peterbilt, Kenworth, Volvo, International, Mack, Western Star and Hino. We are Cummins certified and International certified.

Can I keep driving with the check-engine light on?

Depends on the code. A yellow lamp with no derate and no change in how the truck runs can usually wait for the next scheduled stop. A derate, coolant loss, heavy smoke or a knock should not be driven on. Call and read us the code; we will tell you which it is.

How long does a diagnosis take?

Most trucks get a finding the same day they arrive during shop hours. Intermittent faults can take longer because they have to be reproduced.

Will you replace parts before you know the cause?

No. The estimate comes after the diagnosis names the cause. If teardown finds something new, we stop and call before going further.

Do you do in-frame overhauls?

Yes. Overhauls and cylinder head work are quoted after teardown so the estimate reflects what is actually worn, not a guess from the mileage.

Do you service APUs?

Yes. Thermo King, Carrier, RigMaster and Dynasys units: maintenance, repair and installation.

Is the repair covered if it fails on the road?

Repairs are covered by the NAPA Over the Road Nationwide Limited Warranty for 12 months from the repair date at participating NAPA Truck Care locations across the country. Ask for the warranty document when you pick up the truck.

DPF Cleaning & Regen

Open the page
What is a forced regen and will it fix the problem?

A forced regen is a regeneration started from the diagnostic laptop, with the technician watching soot load drop in real time. It fixes a filter that is soot-loaded. It does not fix an ash-loaded filter, a failed sensor, bad DEF or an engine problem that is loading the filter, which is why we read the data before we start one.

How long can I drive with the DPF light on?

A yellow DPF lamp alone means do a parked regen soon. A regen request you cannot complete, a check-engine lamp with the DPF lamp, or any loss of power means the next stage is a derate. Do not plan a long trip on it. Call us while the truck still moves.

What is the 5 mph derate?

The final inducement stage. The ECM limits the truck to about 5 mph until the fault is repaired and the derate is cleared with diagnostic software. It is usually triggered by DEF system faults or ignored regen requests. It cannot be cleared by shutting the truck off.

Do you clean the DPF or replace it?

We clean it when the substrate is intact. An ash-loaded filter is pulled, cleaned, flow-tested and reinstalled with new gaskets and clamps. A cracked or melted filter is replaced, and we tell you that before we order one.

Can you delete the DPF?

No. It is illegal under federal law, it fails the CARB Clean Truck Check, it voids engine warranties and the penalties land on the owner. We do not do it and we will not sign off on a truck that has had it done.

Why does my truck keep regenerating?

Frequent regens mean the filter is loading faster than normal: short trips and idle time, an ash-loaded filter leaving less room for soot, a leaking injector or turbo seal, or a plugged pressure line fooling the ECM. The regen history tells which.

Can bad DEF cause a derate?

Yes. Low concentration, contaminated DEF, or DEF that has crystallized in the dosing valve will trip SCR efficiency faults and start the derate ladder. We test concentration with a refractometer and check the dosing system before condemning parts.

Truck Brake Repair

Open the page
How often should air brakes be adjusted?

Automatic slack adjusters should hold adjustment on their own. If one needs manual adjustment, it is failing or something in the foundation brake is wrong, and adjusting it by hand hides the problem. Stroke should be measured at every PM and before any inspection.

What is the 20 percent rule?

Under the CVSA out-of-service criteria, when 20 percent or more of the brakes on a vehicle or combination are defective (out of adjustment, inoperative, missing lining, cracked drum and so on), the vehicle is placed out of service on the spot.

Can I drive if one brake is out of adjustment?

On a five-axle combination, one brake out of adjustment is a violation but usually not out of service; two can be. Either way the brake is doing less than its share and the others are overheating to cover it. Get it measured.

Do you work on air disc brakes?

Yes. Pads, rotors, calipers and caliper guide pins on tractors and trailers with air disc brakes. Rotors and some caliper assemblies come next-day from the warehouse.

Do you do trailer brakes?

Yes. Trailer foundation brakes, slack adjusters, chambers, air lines, gladhands and trailer ABS, in the same bay, and timed with the trailer's annual inspection when you want one visit instead of two.

How long does a brake job take?

Measurement about an hour. A shoe-and-drum job on one or two axles usually finishes the same day during shop hours. Full combinations and air disc jobs depend on parts; we tell you after the measurement.

Is the brake work under warranty?

Yes. Repairs carry the NAPA Over the Road Nationwide Limited Warranty for 12 months from the repair date, honored at participating NAPA Truck Care locations across the country.

Heavy-Duty Alignment

Open the page
How often should a semi truck get an alignment?

About once a year as a check, or on the interval in your OEM schedule, and always before new steer tires, after steering or suspension repair, or when you see a pull or edge wear. Catching a toe drift at a PM costs an hour; catching it at a tire change costs tires.

How long does a heavy duty alignment take?

About one to two hours for a tractor. Add time for trailer axles, and for any parts that have to be replaced first.

Can you align trailers as well as tractors?

Yes. Trailer axles are measured against the kingpin and against each other, and adjusted with shims or the adjustable torque rods the trailer design allows. Bring the trailer with the tractor or on its own.

What makes the Hunter HawkEye XL different?

It reads three axles at the same time with long-range HD cameras and non-electric 3D targets, so a tractor's steer and both drive axles come up in one pass with nothing on the wheel to charge or calibrate. Sam's is a Hunter Certified Alignment Center.

Another shop aligned it and it still pulls. Why?

Usually one of three things: only the steer axle was aligned and a drive axle is out of thrust, a worn king pin or tie rod end was aligned around, or the pull is a tire or wheel problem rather than an angle. The three-axle measurement and the parts inspection sort out which.

Do I need the trailer attached?

Not for a tractor alignment. For a trailer alignment we need the trailer. For a combination that dog-tracks or pulls, bring both and we measure the whole rig.

What does an alignment cost?

Call for the current rate. The price depends on tractor, trailer or combination and on whether any parts have to be replaced first, which we tell you after the inspection.

Electrical & AC Repair

Open the page
Why does the truck keep killing batteries?

Usually one of four things: a parasitic draw with the key off, an alternator that is undercharging or overcharging, a corroded cable or ground that keeps the batteries from charging fully, or batteries that have been deep-cycled by inverter loads. We test for all four before selling batteries.

Can you fix trailer lights?

Yes. Marker, tail, brake and turn circuits, the seven-way connector on both ends, and the trailer harness. Lighting is checked to 49 CFR 393 Subpart B, the lamps a roadside inspector looks at.

My AC is blowing warm. Is it just a recharge?

Refrigerant does not evaporate. If the system is low, it leaked. We find and fix the leak, then evacuate and charge by weight. Topping it off without the leak repair means paying for the same refrigerant again in a month.

Do you come out for a no-start?

Yes, in the Toledo area during shop hours. The service truck handles batteries, cables, starters and jump-and-diagnose on site, so you are not paying for a tow to find out it was a ground strap.

How do you find an intermittent fault?

With live data and wiggle tests on the harness while the fault is active, and by looking at where the harness rubs, flexes or gets wet. We do not replace parts in sequence until the light goes out.

The ABS light is on. Can I drive?

The service brakes still work; the ABS function does not. It is a violation at roadside and the truck may not stop straight in a panic stop. Most ABS faults are a wheel speed sensor, a modulator or the power line through the seven-way, and most are same-day repairs.

How long will the truck be here?

Diagnosis is usually the same day. Charging, starting, lighting and most AC jobs finish the same day or next day depending on parts. Harness work takes as long as the damage runs, and we tell you where we are each day.

Welding & Fabrication

Open the page
Do you offer mobile welding in Toledo?

Yes. The service truck carries a welder and does on-site repairs in the Toledo area during shop hours, Monday to Friday 8 to 5: fleet yards, job sites and trailers stuck at a dock. Tell us where the unit is and what broke, and we will say whether it is a service-truck job or a bay job.

Can you weld aluminum truck and trailer components?

Yes. Aluminum work is TIG or spool-gun MIG, with the oxide cleaned off and the correct filler. Floors, side panels, top rails, ramps, tool boxes and brackets.

Can you weld a cracked truck frame?

Only the way the OEM allows. Heat-treated rails lose strength when welded, and 49 CFR 393.201 limits frame welding to the manufacturer's recommendations. Most frame repairs are a crack repair to the OEM spec plus bolted reinforcement plates. When a rail is past repair we say so.

Do you do emergency welding?

During shop hours, yes, front of the line when a trailer or truck cannot move until it is fixed. We do not run outside shop hours.

Can you replace a trailer floor?

Yes. Wood and aluminum floors, the crossmembers under them and the sills they sit on, in sections or in full. Doors, thresholds and ramps at the same time if they need it.

Can you install a PTO and wet kit?

Yes. PTO and wet kit installation for dump trucks, roll-offs and specialty equipment, with hydraulic pump and cylinder repair and hose fabrication done in the same bay.

What does frame or trailer welding cost?

Call for the current rate. Small repairs are quoted on the spot; frame and floor work is quoted after inspection, with the method written out so you can compare it to any other estimate.

CARB Clean Truck Check

Open the page
How long does a CARB emissions test take?

About 30 to 45 minutes for an OBD test and about an hour for an opacity test, during shop hours. The upload to CARB happens during the visit.

What happens if my truck fails the CARB test?

You get the reason, usually an active emissions code, incomplete readiness monitors or missing emissions equipment, and a repair estimate. When the repair is done here and the monitors are set, the retest is free and the pass goes to CARB before you leave.

Do I need an appointment for CARB testing?

No, but booking holds the slot. Walk-ins are tested as the bay opens during shop hours, Monday to Friday 8 to 5.

I am not based in California. Do I still need CARB testing?

If the vehicle is over 14,000 lbs GVWR and operates in California, yes. The program applies to out-of-state registered vehicles, and roadside and scale enforcement in California checks the CARB database regardless of the plate.

What does the CARB test cost at Sam's?

$189 plus tax, flat rate. The retest is free when we do the repair.

How often does the truck have to be tested?

Periodic testing is tied to the vehicle's registration date and currently runs twice a year, with CARB scheduled to raise the frequency for OBD-equipped vehicles in 2027. Your CTC-VIS record shows the compliance deadline. Check it, or ask us when the truck is here.

The check-engine light is on. Can you still test it?

We can run it, but an active emissions fault is a fail. Book the diagnosis first and the test after, so you pay for one test instead of two trips.

Do you upload the results to CARB?

Yes. The tester submits the result to CARB's database in real time during the visit, and you leave with the compliance certificate.

Preventive Maintenance

Open the page
How often should a semi truck get an oil change?

Most current heavy-duty engines run 25,000 to 50,000 miles between oil changes with the OEM-approved oil, shorter for vocational, short-haul and high-idle trucks. Oil analysis can justify the long end of the range. Check your OEM schedule; we keep the common ones on file.

What is the difference between A, B and C service?

A is oil, filters, lube and the walk-around inspection, about two hours. B adds air dryer service, coolant test, battery test, driveline, suspension and brake measurements and an aftertreatment data review, about half a day. C adds the annual DOT inspection under 49 CFR 396.17 and the OEM's long-interval items as they come due, usually one day.

Do you come to our yard?

Yes, in the Toledo area during shop hours. The service truck does A services and inspections at your lot. B and C services and anything that needs a lift happen in the shop.

Do your PM records satisfy a DOT audit?

The records list what was inspected, what was measured, what was repaired and the next due date, by vehicle, which is what 49 CFR 396.3 requires a carrier to keep. Fleet customers get them by unit so the file is ready when the audit letter comes.

Can the annual DOT inspection be part of the PM?

Yes. The C service includes the annual inspection to 49 CFR 396.17 and Appendix A to Part 396 by our qualified inspector, with the report and sticker, so the truck is in the bay once instead of twice.

I have one truck. Is this just for fleets?

No. An owner-operator with one truck gets the same A, B and C services and the same records. The fleet conversation is about scheduling many units; the service is the same.

What if you find something during the PM?

It gets measured, written down and quoted before anything is done. You decide what gets fixed now and what gets scheduled. Nothing is added to the invoice that you did not approve.

Are you a dealer?

No. Sam's Truck & Trailer - A NAPA Truck Care Center is an independent shop. We work on every make, we are not tied to one parts catalog, and the person who quotes your job is in the building.

What trucks do you work on?

Medium and heavy duty, Class 4 through Class 8, trucks and trailers, all makes. Engines, transmissions, brakes, air systems, electrical, AC, suspension, welding and fabrication, and trailer structure, doors, floors, air lines, lighting and landing gear.

Do you come to the truck?

Yes, in the Toledo area during shop hours. The service truck handles on-site repairs, mobile welding and yard PM for fleets. If the job needs a lift or the alignment rack, it comes to the shop.

Are you open on weekends or after hours?

No. The shop is open Monday through Friday, 8:00 AM to 5:00 PM. During those hours a truck that is down goes to the front of the line. After hours, we take it first thing the next morning.

Is the repair covered by a warranty?

Yes. Repairs at Sam's are backed by the NAPA Over the Road Nationwide Limited Warranty, 12 months from the original repair, honored at participating locations nationwide. The warranty page has the details.

Fleet Program

Open the page
What does the fleet program include?

PM scheduling per unit by miles, hours or calendar; the DOT annual inspection on the same visit when due; yard PM from the service truck in the Toledo area during shop hours; consolidated billing with net terms on approval; and the 49 CFR 396 records a fleet needs.

Is there a minimum fleet size?

No. The program is built per unit, so it works for a fleet of three and a fleet of forty. Call and tell us what you run.

Can you handle mixed fleets?

Yes. Class 4 through Class 8, trucks and trailers, all makes. Cummins certified and International certified, with a qualified DOT inspector on staff and the Hunter HawkEye XL for alignment.

Will you come to our yard?

Yes, in the Toledo area during shop hours. The service truck handles yard PM, mobile welding and on-site repairs. Units that need a lift or the alignment rack come to the shop, scheduled ahead.

What records do we get?

Maintenance records under 49 CFR 396.3 for every unit, DVIR repair certifications under 396.11 and 396.13, and 396.17 annual inspection reports, retained for the required periods and available when an auditor or insurer asks.

Do you offer net terms?

Yes, on approval, with a fleet account. One consolidated invoice per period for every unit, every service, every repair, and parts bought over the counter at wholesale pricing on the same bill. Call for the current labor rate.

Warranty

Open the page
How long is the warranty?

12 months from the date of the original repair, for defects in materials and workmanship, subject to the terms and conditions in the warranty document you receive with your invoice.

Does it cover me outside Ohio?

Yes. The NAPA Over the Road Nationwide Limited Warranty is honored at participating NAPA Truck Care Center locations across the country, not only at our shop.

What do I do if a repair fails away from Toledo?

Call us first at (419) 724-2475 during shop hours if you can. We will help you locate the nearest participating location. Have your invoice; the participating shop verifies the original repair and handles the warranty work under the program terms.

What is not covered?

The complete terms, conditions and exclusions are in the warranty document. In general, a repair warranty covers the work that was done and the parts that were installed; it does not cover a different part that fails later, normal wear, or damage from an accident, abuse or missed maintenance.

Do I need to keep anything?

Your invoice. It has the repair date, which starts the 12 months, and the parts and labor that are covered. Fleet accounts have every invoice in their account history.

Perrysburg, OH

Open the page
Do you come out to Perrysburg?

Yes. The service truck runs to Perrysburg, Rossford and the SR 795 warehouse strip during shop hours, Monday to Friday 8 to 5. Yard PM, mobile welding and on-site repairs. Call first so the tech leaves with the right parts.

How far is the shop from downtown Perrysburg?

About 15 miles and about 20 minutes. I-75 north from exit 193 to exit 207 at Stickney Ave, then north on Stickney about a mile to Matzinger Rd.

I just came off the Turnpike at exit 64. How long to you?

About 13 miles, about 17 minutes. I-75 north from exit 195, past downtown Toledo, to exit 207. If the truck will not make it, pull into a lot and call. We dispatch during shop hours.

Can you do a DOT inspection and the alignment in one visit?

Yes. The 49 CFR 396.17 annual inspection takes about an hour and the Hunter HawkEye XL alignment is in the same building. Book both and the truck comes in once.

Maumee, OH

Open the page
Do you send the service truck to Maumee?

Yes, during shop hours, Monday to Friday 8 to 5. Maumee, Arrowhead Park, the Dussel Dr and Salisbury Rd business parks and the Turnpike exit 59 side are all normal mobile calls. Call first so the tech brings the right parts.

Which way is faster from Maumee, the Trail or I-475?

They are close. US-24 Anthony Wayne Trail northeast to I-75 at exit 201, then north to exit 207, is about 16 miles with lights. I-475 north to I-75 at exit 20A, then exit 207, is about 20 miles but all freeway. Either is about 25 minutes outside the rush.

I just came off the Turnpike at exit 59. How far are you?

About 17 miles, about 22 minutes. Dussel Dr west to I-475 north, I-475 to I-75 north at exit 20A, I-75 to exit 207, then Stickney Ave north about a mile.

Can you align a tractor and a trailer?

Yes. The Hunter HawkEye XL handles steer, drive and trailer axles. Call for the current rate and we will book a slot so you are not waiting.

Northwood & Oregon, OH

Open the page
Do you come out to Northwood and Oregon?

Yes. Both are inside the service truck's normal range during shop hours, Monday to Friday 8 to 5. Yard PM, mobile welding and on-site repairs at the distribution centers along I-280 and SR 795 are routine calls for us.

What is the fastest way from Northwood to the shop?

I-280 north to the end, where it meets I-75. Follow the ramp for I-75 south toward downtown, take exit 207 at Stickney Ave, and go north on Stickney about a mile to Matzinger Rd. About 10 miles, about 15 minutes.

I am at the truck stops at the Turnpike and I-280. How far are you?

About 13 miles, about 18 minutes. I-280 north from exit 1B all the way to I-75, then exit 207 and Stickney Ave north. If the truck cannot move, call and we will send the service truck to the lot.

Do you repair trailers, or just tractors?

Both. Trailer structure, doors, floors, air lines, lighting, landing gear and brakes. Mobile welding on a trailer that cannot roll is one of the most common calls we get from the I-280 warehouses.

Sylvania, OH

Open the page
Do you send the service truck out to Sylvania?

Yes, during shop hours, Monday to Friday 8 to 5. Sylvania, Sylvania Township and the US-23 side of Lucas County are inside our normal mobile range. Call first so the tech leaves with the right parts on the truck.

How long is the drive from Sylvania to the shop?

About 14 miles and about 20 minutes outside rush hour. US-23 south onto I-475 east, I-475 to I-75 north at exit 20A, then I-75 exit 207 at Stickney Ave. Stickney north about a mile to Matzinger Rd.

Can you do my annual DOT inspection while I wait?

Usually. The 49 CFR 396.17 inspection takes about an hour. If something fails, the repair happens in the same bay and we tell you before we start. Call and we will hold a slot.

What if the truck breaks down on US-23 or I-475?

Call (419) 724-2475 during shop hours. Emergency calls go to the front of the line and we dispatch the service truck or clear a bay. Get the rig fully onto the shoulder and set your triangles first.

Bowling Green, OH

Open the page
Is Bowling Green too far for the service truck?

Not for scheduled work. Yard PM and planned on-site repairs in Bowling Green are booked in advance during shop hours, Monday to Friday 8 to 5. For a breakdown on I-75 near Bowling Green, call and we will tell you honestly whether the truck or a tow to the bay is faster.

How long is the drive from Bowling Green?

About 28 miles and about 32 minutes. I-75 north from exit 181 all the way to exit 207 at Stickney Ave in north Toledo, then north on Stickney about a mile to Matzinger Rd.

Why drive to Toledo instead of a shop closer to Bowling Green?

Four technicians, a DOT inspector on staff, the Hunter HawkEye XL alignment system, Cummins and International certification and NAPA Truck Care Center backing. Most repairs are done the same day, depending on parts, so one trip up I-75 usually ends with the truck fixed.

Can you do the annual DOT inspection while I wait?

Usually. The 49 CFR 396.17 inspection takes about an hour. Anything it turns up is repaired in the same bay and we tell you before we start.

Findlay, OH

Open the page
Findlay has truck shops. Why would I drive to Toledo?

Three reasons we hear. The truck is already headed north and the shop is on the way. The Findlay shops are booked out and the truck is losing money every day it waits. Or you need something specific: a Hunter HawkEye XL alignment, a CARB Clean Truck Check, or a DOT inspection and the repair in one visit.

Do you send the service truck to Findlay?

Only for scheduled fleet work, booked in advance during shop hours, Monday to Friday 8 to 5. For a breakdown near Findlay, we will tell you honestly that a closer tow is usually the right call, and we will take the truck when it gets here.

How long is the drive from Findlay?

About 50 miles and about 50 minutes. I-75 north from exit 159 straight through Bowling Green, Perrysburg and downtown Toledo to exit 207 at Stickney Ave, then north on Stickney about a mile to Matzinger Rd.

Can you get a Findlay truck in and out the same day?

Often, depending on parts. Call before you leave Findlay, tell us the symptom and the unit, and we have the bay and the likely parts ready when you pull in. If it is going to be more than a day, we tell you before you make the drive.

Monroe, MI

Open the page
You are in Ohio. Do you come up to Monroe?

Yes. Monroe is about 20 miles up I-75 and inside the service truck's range during shop hours, Monday to Friday 8 to 5. Yard PM, mobile welding and on-site repairs. Call first so the tech leaves with the right parts.

How long is the drive from Monroe to the shop?

About 21 miles and about 25 minutes. I-75 south across the state line, past Alexis Rd, to exit 207 at Stickney Ave in north Toledo. Then north on Stickney about a mile to Matzinger Rd.

Does a Michigan truck need anything different for a DOT inspection?

No. The 49 CFR 396.17 annual inspection is federal. Our qualified inspector does it the same way for a Michigan plate as an Ohio plate, about an hour, and any repair happens in the same bay.

I just got pulled in at the weigh station and put out of service. Can you help?

Call (419) 724-2475 during shop hours. Tell us what the officer wrote up. Brakes, lights, air leaks and tires are the common ones, and the service truck carries parts for most of them. If it needs the bay, we clear one.

I-75 through Toledo

Open the page
Which I-75 exit is the shop?

Exit 207, Stickney Ave / Lagrange St, mile 207 in north Toledo. North on Stickney Ave about a mile, then right on Matzinger Rd. We are just east of Stickney, between the I-475 junction at 204 and the I-280 split at 208.

I am northbound and already passed exit 207. What now?

Take exit 210 at Alexis Rd, get back on I-75 south, and take exit 207 southbound. About 5 extra miles. Do not try Ottawa River Rd at 209; it does not connect through to Matzinger.

How far up and down I-75 does the service truck go?

During shop hours, Monday to Friday 8 to 5, the service truck covers I-75 from about Bowling Green to Monroe, Michigan. South of Bowling Green we will usually suggest a tow to the bay and tell you why.

What should I tell you when I call from the shoulder?

Direction, the last exit you passed, and what the truck is doing. A derate and a DPF light, air that will not build, a blown tire, a reefer alarm. That tells us whether the service truck or the bay is the faster fix and what parts to load.

Ohio Turnpike, I-80/90

Open the page
Which Turnpike exit gets me to the shop fastest?

Exit 64, I-75. North about 12 miles to exit 207, Stickney Ave, then north on Stickney about a mile to Matzinger Rd. About 13 miles and about 17 minutes from the toll plaza.

I am at the truck stops at exit 71. Can you come to me?

Yes, during shop hours, Monday to Friday 8 to 5. The TA, Petro, Pilot Flying J and Love's lots at exit 71 and I-280 exit 1B are about 15 miles from us and a routine run for the service truck. Call with the lot and the symptom.

Can the service truck come onto the Turnpike itself?

The Turnpike has its own rules for service vehicles on the toll road. If the truck will still move, get to the next exit or a service plaza and call us from there. If it will not move, call us and we will tell you honestly what the fastest path is.

Does it matter whether I am eastbound or westbound?

Only for which exit comes first. Eastbound from Indiana you hit 59, then 64, then 71. Westbound from Cleveland you hit 81, then 71, then 64. Exit 64 is the shortest route to the shop from either direction.

I-280 & US-23, Toledo

Open the page
Where exactly is the shop relative to I-280?

I-280 ends at I-75, exit 208. The shop is at I-75 exit 207, one exit south, then about a mile north on Stickney Ave to Matzinger Rd. From the end of I-280 it is about 2 miles and about 5 minutes.

Can you come to the truck stops at I-280 exit 1B?

Yes, during shop hours, Monday to Friday 8 to 5. The TA, Petro, Pilot Flying J and Love's lots at exit 1B are about 13 miles from us and a routine run for the service truck.

What about US-23 north of I-475, toward Michigan?

US-23 from the I-475 split to the state line is only about 3 miles and we cover it. Take US-23 south onto I-475 east, I-475 to I-75 north, exit 207. About 14 miles from Sylvania.

Do you work on reefers and trailers, or only power units?

Both. Reefer units, trailer brakes and air lines, doors, floors, landing gear and lighting. The service truck can handle a lot of trailer work right at the dock.

Got it.

Need it sooner? (419) 724-2475

Hours Mon–Fri 8–5
820 Matzinger Rd
Call now